Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
Just how do you feel on the subject of Installing A Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately hard job. If the old bathtub is readily available, the job can relocate easily; if you have to open a wall to remove the old bathtub and also position the new bath tub, the job is a lot harder. In either case, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub and embeded in the new one. See to it you have qualified on your own for the work as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This short article will assist you set up a brand-new bathtub in your washroom if you have actually already purchased a brand-new tub and also don't need to alter the setup of your previous water pipelines.
Your devices as well as material list ought to make up the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bathroom should be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic as a result of the limited accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipes. When the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, place the bath tub in the needed placement. The wooden boards are valuable in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bath tub up until the spirit level reads level.
To set up taps, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water system as well as check all joints and also new pipework for leaks as well as tighten them if essential. Load the bath tub and additionally check the overflow outlet and the regular outlet for leakages.
Lastly, fix the bath paneling as described in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been utilized a minimum of once as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in place between the faucet and the sink. Safeguard the faucet in position with the maker provided backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous kind must be linked to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to penetrate the wall surface in between the bath and the tiling, bring about complications with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before sealing, to permit the activity experienced when the tub is in use. The sealant can crack rather early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very interested by Installing A Bathtub and I am assuming you liked my blog posting. Enjoyed reading our review? Please share it. Help somebody else find it. We cherish reading our article about How to Install a Bathtub.
Professional touch? Contact. Report this page